Chemically modified organic/inorganic nanoporous composite particles for the adsorption of reactive black 5 from aqueous solution

In the present work, we report a chemically modified polyacrylamide/silica nanoporous composite adsorbent for the removal of reactive black 5 (RB5) azo dye from aqueous solutions. The composite adsorbent was synthesized in a packed bed and modified by ethylenediamine (EDA). The adsorbent was characterized by Fourier transformation infrared (FT-IR), thermogravimetric analysis (TGA), thermoporometry, Brunauer, Emmett and Teller (BET) method and scanning electron microscopy (SEM). Mechanical stability of the adsorbent was examined in a packed bed by following the back-pressure of the column. Pore diameter of the composite adsorbent in dry and wet states was estimated to be about 18.71 nm and 12.61 nm, respectively. Adsorption experiments were performed in batch mode and effect of various operational parameters on the adsorption capability of the adsorbent was studied systematically. The maximum adsorption capacity of the modified composites was found to be 454.5 mg RB5/g of adsorbent. The equilibrium data were analyzed by Langmuir, Freundlich, Sips, BET and Redlich–Peterson isotherm models and found to fit well to the BET isotherm. The data kinetically followed the pseudo-second-order model. High adsorption capacity, fast removal mechanism, and good mechanical stability are three advantages of the presented composite for the removal of RB5.     

超细粉在内循环流化床中的流态化特性

在内径120 mm的半圆柱形内循环流化床中,以平均粒径387 nm的Ti O2为原料,考察了单独通入流化气、射流气和同时通入流化气和射流气三种流化方式下超细粉的流化特性以及射流气速对超细粉聚团尺寸的影响。结果表明:同时通入流化气和射流气时,流化气能促进粉体循环,消除环隙死区;高速射流能有效破碎聚团,显著减小聚团尺寸,从而使超细粉在环隙区与导流管之间形成稳定循环,小聚团在环隙区实现平稳流态化。随着射流气速的增大,聚团尺寸减小,粒度分布变窄,在射流气速分别为60,90,120,150 m/s的条件下,聚团平均直径分别为194,158,147,135μm。     

超细粉体抑爆装置瞬态喷射特征参数

在敞开空间开展了容积为2 L及5 L的超细粉体抑爆装置瞬态喷射参数研究，重点介绍了5种典型装配条件下的喷射性能，并对相关特征参数进行定量分析。结果表明：抑爆剂喷射所形成的超细粉体云幕特性由气体发生器装配结构和膜片开启压力共同决定，但两者之间必须恰当配置，作用在膜片上的能量份额较大时，膜片开启状态恶化，抑爆器腔体聚压不足，抑爆剂二次喷射严重，反之膜片不能正常开启。装配优化后的I型抑爆器在触发后10 ms内腔体聚压达到峰值，膜片破裂后5 ms内抑爆剂全部喷射，喷射动态性能较好，在第1个100 ms内扩散速度达到15 m/s，在第2个100 ms内扩散速度约13 m/s，0~1 000 ms内平均扩散速度约8 m/s，扩散过程较为连续，不存在二次喷射现象，喷射距离可达到7.5 m，抑爆剂质量分布呈渐进增长，产生的超细粉体云幕特征参数优良。Ⅱ型抑爆器两种装配的喷射表明：当抑爆装置中压力上升历程及压力峰值较为接近时，抑爆剂粉体喷射特性无显著差异。上述结论的可重复性得到了数百次喷射实验的验证。     

气化灰基腻子粉的制备与性能研究

为实现气化灰综合利用和降低腻子粉制备成本，研究了利用气化灰替代水泥制备腻子粉的技术可行性。以气化灰和 42.5水泥为主要原料，配以少量的羟丙基甲基纤维素和可分散性乳胶粉，制备气化灰基腻子粉，实验考察原料配方变化对腻子粉的性能影响。研究结果表明：利用气化灰替代水泥制品制备腻子粉具有可行性。其中，气化灰替代 50%水泥时，腻子粉的粘结强度为 0.82 Mpa，各项性能均优于建筑外墙用腻子粉标准 JG/T 157—2009要求。在相同条件下，气化灰替代不超过 70%的水泥时，腻子粉的粘结强度及其他指标均满足建筑外墙用腻子粉标准 JG/T 157—2009要求。     

Study of fragmentation in cBN powders under ultra-high pressure

Studying the fragmentation law and refinement of cubic boron nitride powder under ultra-high pressure is crucial to producing a high-strength, high-density polycrystalline cubic boron nitride. In this paper, brown and black cBN crystalline powders with different micron sizes were selected as initial raw materials for an ultra-high-pressure simulation experiment. Single and mixed particles were extruded under 80MPa low pressure and 5.5GPa ultra-high pressure at ambient temperature for 1 min. The crushing behavior and particle size distribution of cBN powders with different particle sizes and ratios were investigated using a laser particle size analyzer and scanning electron microscopy. Results revealed no particle breakage or deformation at low pressure, and the compaction density was low. However, under ultra-high pressure, the cBN particles showed cracks, plastic deformation, and fragmentation, resulting in crushed fine particles filling in the voids of coarse particles, which led to a higher pressing density. Small-sized or mixed cBN particles with high density ratios were not easily crushed; the coarser the particle size, the more severe the ultra-high-pressure extrusion and crushing. The pressing density also declined, and brown cBN crystal particles with higher impact toughness demonstrated a lower particle breakage rate. The ultra-high-pressure crushing law should be considered and appropriate binders should be selected to improve the sintering performance of PcBN materials; ultra-high-pressure crushing of cBN powder contributes to cBN-cBN and cBN-M-cBN bonds under high temperatures and ultra-high pressure.     

超声波辅助插层-剥离法制备煤系高岭土微粉的研究

我国煤系高岭土储量丰富,为满足造纸、纺织等行业个性化的需求,通常要对其进行深加工。以山西朔州煤系高岭土为原料,分别在恒温磁力搅拌和超声波作用下探究了煤系高岭土/二甲基亚砜(DMSO)插层复合物制备的最佳条件,在插层复合物的基础上对煤系高岭土进行超声辅助剥离,制备得到高岭土微粉,并利用XRD、SEM、BET、TG-DSC等方法分析表征样品。正交实验结果表明在磁力搅拌条件下DMSO用量、插层时间以及插层温度均对插层率具有一定的影响,引入超声波有利于高岭土插层率的提升。插层复合物经超声辅助剥离后晶粒厚度明显减小,高岭土片层状结构大体上呈现碎片化,仅保留少部分大的片状结构,其边缘碎化,整体上也出现碎裂的趋势。剥离样品的比表面积和孔径均大幅度增加,为硬质高岭土的剥离和超微细粉体的制备提供了新的思路。     

Effects of different drying methods on the physicochemical property and edible quality of fermented Pyracantha fortuneana fruit powder

In this study, hot air drying (HAD), hot air-/microwave-assisted vacuum drying (HAMAVD) and hot air-assisted microwave drying (HAAMD) were applied to lactic acid-fermented Pyracantha fortuneana fruit (PFF). Influences of different drying methods on fluidity and dispersion, microstructure, hygroscopicity, rehydration, colour change, sourness and energy consumption were investigated. Results showed that HAAMD had the best overall performance on the quality of the PFF powder. HAAMD PFF powder had higher expansion force (1.65 mL g⁻¹) and water-holding capacity (2.68 g g⁻¹), lower degree of compression (9.09%) and energy consumption, smaller colour change and better taste. Organic acids (mainly malic acids) of all drying powders decreased, but HAAMD and HAMAVD could better improve the acidity characteristics of PFF powders, which may be related to the drying time and the temperature change processes. Consequently, this study can provide references for the utilisation of fresh PFF, the design and commercialisation of PFF-related products.     

Effect of Si/Ti additions on physico-mechanical and chemical properties of FeNiCrCo high entropy alloys manufactured by powder metallurgy technique

FeNiCrCoSi_x and FeNiCrCoTi_x (x=0, 0.3, 0.6, and 0.9 wt.%) high entropy alloys (HEAs) were prepared via the powder metallurgy technique. A homogenous distribution of the elements in all alloys due to the formation of a solid solution phase is observed. The density and hardness of the prepared HEAs are improved by Si and Ti additions, compared to FeNiCrCo HEA. The wear rate of the prepared alloys was studied at different loads and the results indicate that the alloys that contain 0.3 wt.% Si and 0.9 wt.% Ti have the lowest wear rates. X-ray diffraction, SEM, and EDX were used to understand the phases, grain sizes, and microstructures in different investigated HEAs. The effects of Si and Ti content on the corrosion behavior and surface morphologies of sintered FeNiCrCoSi_x and FeNiCrCoTi_x HEAs were studied by immersion in H₂SO₄, HNO₃, and HCl solutions. Uniform corrosion and localized pitting are observed in different sizes in the corrosive media used. Because of the smaller pit size and the reduced pit density, the FeNiCrCoSi_0.3 HEA has an excellent microstructure.     

Effect of Fe doping on structure,magnetic and electrical properties La0.7Ca0.3Mn0.5Fe0.5O3 manganite

The crystal and magnetic structures of La_0.7Ca_0.3Mn_0.5Fe_0.5O₃ compound have been studied by neutron powder diffraction in the temperature range of 10–300 К. The magnetization and electrical resistivity measurements have been also performed in the temperature range of 5–300?K in magnetic fields up to 1?T. These experimental results indicate a formation of a complex magnetic state in which the long-range antiferromagnetic G-type phase coexists with the short-range ferromagnetic clusters. The electrical conductivity of La_0.7Ca_0.3Mn_0.5Fe_0.5O₃ demonstrates an anomalous temperature behavior suggesting a switching between different states. The origin of the unconventional magnetic state, the mechanisms of the electrical conductivity, and correlation between magnetic and transport properties in this manganite have been discussed.